Tutorials

How to check hard drive and if it works well 【step by step】

Table of contents:

Anonim

Many of you may wonder: How to check hard disk and if it works well ? Well, checking the hard drive is almost mandatory from time to time or even when we buy a new one. If it doesn't work for you, go in.

Our hard drives need good maintenance, like good use. As a technological device, it requires certain check-ups that can help us diagnose certain errors or rectifiable problems. So, we have put together this guide so that you can check your hard drive correctly.

We hope you like our methods with programs and without programs. Let's get started!

Index of contents

Method # 1: CHKDSK

As you will see, first there will be the methods that can be performed without downloading any program. Later, we will get into the dust to tell you which tool is better.

In this method we are going to scan our hard drive to find errors or problems in the sectors. The good news is that they can be solved, but the bad news is that we cannot, if they are bigger than we think.

So, to use CHKDKS, we are going to go to " This team ", we right click on the one we want and we go to the " Properties " menu.

Within " Properties ", we go to the " Tools " tab. Once there, we click on " Check " where it says " Error checking ". You give it to examine and, when it finishes, it will tell you if there are errors or not.

As you can see this tool is to diagnose any error that exists on our hard drive. But, if we have mistakes, we can go much further.

  • We open Start Menu and write " cmd ". Open the command prompt as administrator. Here we have to think about the hard disk that we want to fix. You go to “ This team ” and look for the letter that has (C:), (F:), etc. Close unnecessary processes or programs that you don't need right now. Depending on the action, we will use one parameter or another. If we want to correct errors on the disk, the parameter is / f; if we want to correct errors in the disk sector, the parameter is / r. Look at the following example:

chkdsk "HDD letter" "parameter"

When the WMI interface is ready, type the following and hit enter:

diskdrive get status

In my case, my hard drives are " OK ", so I have no problem.

Method # 3: CrystalDiskMark

It is considered a " must have " on every PC because it is a very good tool to check the speeds of our hard disk, either reading or writing. It is true that its treatment is " benchmark ", but it can illustrate us a lot about the speeds of our hard drive.

At the end of the day, our SSD or M.2 must go at a certain speed, so it is a good way to check that speed. The test can be light or it can be heavier, depending on how you want to do it. However, I would recommend you continue reading below because there is an ideal program to find out the state of our hard drive.

You can download it at this link: link.

Method # 4: CrystalDiskInfo

Be careful because they are two different programs. The former serves as a benchmark, but this does not. This program focuses on giving interesting information about our hard drives. If the hard drive is nearing its end, the "state of health" will tell.

I would like you to take a look at a very interesting section: that of the times turned on and the hours. I say this because the first thing we should do when we buy a hard drive is to look at the times it has been on and the hours it has been on. In this way, we can see if we are being strained cat by hare.

WE RECOMMEND YOU Anvil's Storage benchmark: What is it and what is it for?

Be careful: this happens with a new or a reconditioned disk.

Download it here: link.

Method # 5: HD Tune

Perhaps HD Tune is not as well known, but it is a very good benchmark utility , as well as diagnosing failures of our hard drives. We know that it is perhaps a somewhat old utility, but it works in a great way and, above all, very visual.

We recommend reading 5 SMART errors that anticipate the death of your hard drive

After each test, the program will show us a graph with the transfer speeds. Unfortunately, it has a much better paid version, but try the free one first.

You can download it here: link.

Method # 6: HDDScan

Finally, this program may interest you because it is an alternative to all the ones we have listed above. It does the same as the others, but it may have a clearer and more basic interface.

We recommend it because it works very well and because it can detect problems you have on your hard drive.

We recommend the best hard drives on the market.

So far our guide to check the status of your hard drive, detect errors and fix them. If you have any questions, you can let us know below. Which one do you use? Did you fix the errors of your hard drives?

Tutorials

Editor's choice

Back to top button