▷ Hard drive error 【best solutions】?

Sometimes we make a mistake in the use of our hard drives, which causes errors in the sector, errors in partitions, etc. We know how important the information that you keep on a hard disk is, so we have tried to collect all the typical or common errors that occur in them. Therefore, if you have an error on the hard drive, read below.

Index of contents

Examine and repair unit

This method is very simple and can help us to repair a minor error that we have on the hard drive. We simply have to go to " This Team " and do the following:

We right-click on the hard drive that we want. We select " Properties ". We go to the " Tools " tab. We give " Check " and we will examine the problems quickly and easily.

CHKDSK

It is the simplest and most basic method of all. It is used to diagnose failures in the hard disk or in one of its sectors. It can solve most of the problems causing inaccessibility to the hard disk in question. In principle, it could be like this:

We open Start Menu and write " cmd ". We enter command prompt as Administrator. We have to write " chkdsk " the letter of the hard disk in question and two possible commands: / r or / f, one to repair errors in the sectors and the another to repair errors on the hard disk. For example, we could write the following.

chkdsk C: / f

And later

chkdsk C: / r

This method works for both internal hard drives and external hard drives. As you can see, it is very simple, although it may not work for you. Therefore, we continue below with more methods.

We recommend reading:

Best SSD on the market

Repair volume

If you have Windows 10, we can repair the volume of the hard disk by accessing Windows PowerShell. Don't be scared because you don't have to download any program, nor is it more complicated than it should be. The process is the following:

We open Start Menu and write " Powershell " We run as Administrator. We write the following:

Repair-Volume C -Scan

If your disk has any letter other than " C: ", change the "C" of the command to the letter of the hard disk you have.

As long as you run, you will be repairing the volume. Do not interrupt the process because it does not take even 1 minute. If you had no errors, it will tell you " NoerrorsFound ". In my case, it had no errors, but we are going to put ourselves in the case that it has detected errors.

We wrote:

Repari-Volume (the letter you have) -OfflineScanAndFix

We press " enter " and it will begin to perform operations. When it finishes, restart the computer. Once you are logged in, do the same steps again to see that the errors have been repaired.

Windows image repair

This process is c

Characterized by using the Windows installation wizard to repair startup or any problem on the hard drive. In this case, the method is focused on hard drives that have startup or startup problems.

For this, we will have to make a bootable USB, so I refer you to this guide we made to carry out the process.

Once we have the bootable USB with Windows 10 we install, restart the computer, change the boot priority as we have said in the mentioned guide and get into the Windows assistant.

Started the wizard, click on next, but notice that there is an option called " repair the computer " right on the screen that says " Install now ". We will get a screen and we will click on " Troubleshoot ". Now, in " options advanced ". Finally, " startup repair ".

Now, Windows will diagnose our hard drive and try to repair it, if it finds faults.

Check faults in control panel

Another method to know that our equipment works correctly, is to go to the " Security and maintenance " section. Here, we will verify that the hard drives are perfect. To access this section, do the following:

Open the start menu and write " control panel ". Open it and go to " Security and maintenance ". If you can't find the section, you probably have the " view by category ". Make sure this way.

When we have entered this section, unfold the central tab of " Maintenance ". Notice that the " Unit Status " is "correct" and that a message states that all units are working correctly.

Error "Windows detected a problem with the hard disk"

Some may have problems with the hard drive and you get a similar message. Many times, this occurs because the hard disk is nearing its end of life, so try to make a backup of all the information you have on it.

The first thing you should do is to corroborate the existence of the error with " scannow ". Do it this way:

Open the Start Menu and write " cmd " (run as administrator). Write the following:

sfc / scannow

It will start scanning the entire hard drive for faults.

If the hard drive is external, write this (replace the letter with that of your hard drive):

sfc / scannow / offbootdir = c: \ / offwindir = c: \ windows

In my case, I do not have any errors, nor violation of integrity. But, assuming someone has an error, write this (replace the letter with whatever you want):

chkdsk C: / f / r / x

Using third-party programs

If none of the mentioned methods has worked for us, we will have to download a program to perform maintenance tasks on our hard drives. There are many tools of this type, so we recommend the ones that work best.

WE RECOMMEND YOUHow to enable fast boot in Windows 10

Health Monitor: CrystalDiskInfo

It is a very simple program to use: install and start r. It simply tells us the temperature of our hard drive, its state of health and some other relevant data, such as the hours on or the number of starts.

It is a functional utility that can warn us of an impending failure or indicate any other error that occurs. Who knows? Maybe it can alert us to back up because the hard drive is coming to an end.

If you want to download it, you can do it here.

Repairman: Disk Drill

This tool is very interesting because it is very easy to use and we can enjoy various functions, such as data recovery, etc. In addition, it offers us the availability of various tools to monitor, clean, protect or make backup copies of our HDDs.

You could say that it is a kind of useful toolkit that helps us properly maintain our hard drive.

Download it here.

Optimizer: WinDirStat

In the event that we have a corrupt hard drive, WinDirStat can offer us a solution to repair it. Not only that, but it helps us optimize the use of our hard disk, eliminating applications or junk files that take up space without need.

After using it for a while, I found it quite interesting and, of course, functional. Like its companions, it is free, although there are always more complete paid versions.

Your download at this link.

Cleaner: DBAN

DBAN is a tool that helps us clean our hard disk, especially if it is damaged. Therefore, it provides us with the possibility of transferring data from one hard disk to another without problems. On the other hand, it is compatible with macOS too, an important aspect for many.

In the event that we want to format or delete, DBAN will leave your hard disk as its initial state, that is, clean as a whistle. It also has functions like data recovery , for example. You can download it here

We recommend the best hard drives on the market

So far our guide on how to repair errors on your hard drive. There are endless possible scenarios regarding our hard drives, so please be patient. We hope this article has helped you. If you have any questions, let us know below. Have these methods helped you? What problems did you have?